*A:vRR# configure router interface "PC3" port 1/1/3Ģ.9 Linux Core Configuration - sudo echo "ifconfig eth0 192.168.3.2 netmask 255.255.255.0" > echo "route add default gw 192.168.3.1" > /usr/bin/filetool.sh -bĢ.10 IP Address Configuration for Port 1/1/4 *A:vRR# configure router interface "PC2" port 1/1/2Ģ.7 Linux Core Configuration - sudo echo "ifconfig eth0 192.168.2.2 netmask 255.255.255.0" > echo "route add default gw 192.168.2.1" > /usr/bin/filetool.sh -bĢ.8. IP Address Configuration for Port 1/1/3 Note: The interface Ethernet 1 is represented by the port 1/1/1 in TiMOS configuration.Ģ.5 Linux Core Configuration - sudo echo "ifconfig eth0 192.168.1.2 netmask 255.255.255.0" > echo "route add default gw 192.168.1.1" > /usr/bin/filetool.sh -bĢ.6 IP Address Configuration for Port 1/1/2 *A:vRR# configure router interface "PC1" port 1/1/1 Password is not sudo echo "ifconfig eth0 10.10.10.2 netmask 255.255.255.0" > echo "route add default gw 10.10.10.1" > /usr/bin/filetool.sh -bĢ.4 IP Address Configuration for Port 1/1/1 The config file of vSIM router can be displayed with the command: To ping an IP address of the host connected to a management interface of vSIM issue the command: Use BOF command-line interface (CLI) to configure IP address for CPM interface. The interface eth0 is connected to CPM management interface. Navigate to Edit -> Preferences -> QEMU VMs and configure VM parameters according to the picture below.Ģ.2 IP Address Configuration for Control Proccessor Module (CPM) Management Ethernet Interface A table mapping vSIM ports and how they are presented in TiMOS configuration is following: They are six Linux Core hosts connected to the ports of virtual service router. Picture 3 - Port Connectivity Testing Topology We are going to create a simple topology in order to check network connectivity between vSIM ports and Core Linux hosts. Now we can connect vSIM virtual machine to connect to GNS3. *A:vRR# configure card 1 mda 1 mda-type "m5-1gb-sfp-b" We have to specify slot and mda type and save configuration. There is a one unprovisioned module m5-1gb-sfp-b equipped in port one of card iom3-xp-b that provides five Ethernet interfaces. Picture 2 - Card iom3-xp-b Provisioned in Slot 1Ĭard iom3-xp-b accepts up to two Media Dependent Adapters (MDAs). *A:vRR# configure card 1 card-type "iom3-xp-b" Thus we mustto provision it for the slot 1. Picture 1 - Card iom3-xp-b is Detected but not ProvisionedĬard IOM3-XP-B is equipped in slot 1 of chasis but it is not provisioned. Login with username admin and password admin.Ĭheck cards that are presented presented in a system with the command: Telnet to a serial port of virtual machine with the command: serial telnet:localhost:3366,server,nowait -smp 2 To start Qemu virtual machine use the command: Now a virtual disk sros-vm.qcow2 is extracted. Qemu additional parameters: -nographic -enable-kvm.Virtual Machines Software and Hardware Requirements
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |